AMCC 3WARE 9590SE Betriebsanweisung Seite 45
- Seite / 110
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Controller Object Commands
www.3ware.com 39
Example:
//localhost> /c2 show unitstatus
Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy
-------------------------------------------------------------------------
u0 RAID-5 OK - - 64K 596.004 ON OFF
u1 RAID-0 OK - - 64K 298.002 ON OFF
u2 SPARE OK - - - 149.042 - OFF
u3 RAID-1 OK - - - 149.001 ON OFF
/c
x
show all
This command shows the current setting of all of the following attributes on
the specified controller: achip, allunitstatus, autocarve, bios, driver,
drivestatus, firmware, memory, model, monitor, numports, numunits,
numdrives, ondegrade, pcb, pchip, serial, spinup, stagger, and unitstatus
Example:
//localhost>> /c0 show all
/c0 Driver Version = 3.00.03.058
/c0 Model = 9690SA-8E
/c0 Available Memory = 448MB
/c0 Firmware Version = FH9X 4.03.00.012
/c0 Bios Version = BE9X 4.01.00.008
/c0 Boot Loader Version = BL9X 3.08.00.001
/c0 Serial Number = 3ware Internal Use
/c0 PCB Version = Rev 032
/c0 PCHIP Version = 2.00
/c0 ACHIP Version = 1501290C
/c0 Controller Phys = 8
/c0 Connections = 10 of 128
/c0 Drives = 10 of 128
/c0 Units = 2 of 128
/c0 Active Drives = 7 of 128
/c0 Active Units = 2 of 32
/c0 Max Drives Per Unit = 32
/c0 Total Optimal Units = 2
/c0 Not Optimal Units = 0
/c0 Disk Spinup Policy = 1
/c0 Spinup Stagger Time Policy (sec) = 1
/c0 Auto-Carving Policy = off
/c0 Auto-Carving Size = 2048 GB
/c0 Auto-Rebuild Policy = off
/c0 Controller Bus Type = PCIe
/c0 Controller Bus Width = 4 lanes
/c0 Controller Bus Speed = 2.5 Gbps/lane
Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy
----------------------------------------------------------------------------
--
u0 RAID-5 OK - - 64K 134.07 ON OFF
u1 RAID-0 OK - - 64K 67.0352 ON OFF
VPort Status Unit Size Type Phy Encl-Slot Model
----------------------------------------------------------------------------
p0 OK u0 68.36 GB SAS - /c0/e0/slt0 HITACHI HUS151473VL
p1 OK u0 34.25 GB SAS - /c0/e0/slt2 MAXTOR ATLAS15K2_36
p2 OK u0 34.25 GB SAS - /c0/e0/slt3 MAXTOR ATLAS15K2_36
p3 OK u0 34.24 GB SAS - /c0/e0/slt4 FUJITSU MAX3036RC
- CLI Guide 1
- Copyright 2
- Trademarks 2
- Disclaimer 2
- Table of Contents 3
- About this CLI Guide 7
- Introduction to the 3ware 8
- Command Line Interface 8
- Supported Operating Systems 9
- Terminology 9
- Installing the 3ware CLI 10
- Run CLI 11
- Install Software. If the 11
- Working with 3ware CLI 12
- Scripting examples 14
- Conventions 15
- RAID Concepts 16
- Available RAID Configurations 17
- Single Disk 22
- Hot Spare 23
- Support for Over 2 Terabytes 25
- CLI Syntax Reference 26
- Syntax Overview 28
- /c1 add type=raid1 disk=0-1 29
- Shell Object Commands 30
- [force] 34
- Controller Object Commands 35
- /cx show achip 38
- /cx show allunitstatus 38
- /cx show autocarve 38
- /cx show autorebuild 39
- /cx show bios 39
- /cx show carvesize 40
- /cx show ctlbus 40
- /cx show driver 40
- /cx show drivestatus 40
- /cx show firmware 41
- /cx show memory 42
- /cx show model 42
- /cx show monitor 42
- /cx show numports 42
- /cx show numunits 43
- /cx show ondegrade 43
- /cx show pcb 43
- /cx show pchip 43
- /cx show serial 44
- /cx show spinup 44
- /cx show stagger 44
- /cx show unitstatus 44
- show alarms [reverse] 46
- show diag 46
- show phy 47
- show rebuild 47
- show selftest 49
- show verify 51
- Example: type=raid5 52
- For the 7/8000 55
- rescan [noscan] 56
- add rebuild= 58
- add verify= 59
- Setting Up a Verify Schedule 59
- add selftest= 60
- set selftest=enable 62
- [task=UDMA 62
- set carvesize=[1024..2048] 64
- set autorebuild=on 64
- start mediascan 66
- stop mediascan 66
- Unit Object Commands 67
- /cx/ux show autoverify 69
- /cx/ux show cache 69
- /cx/ux show identify 69
- /cx/ux show ignoreECC 69
- /cx/ux show initializestatus 70
- /cx/ux show name 70
- /cx/ux show qpolicy 70
- /cx/ux show rebuildstatus 70
- /cx/ux show serial 71
- /cx/ux show status 71
- /cx/ux show storsave 71
- /cx/ux show verifystatus 71
- RaidType 79
- Migration Process 82
- Example of splitting a mirror 83
- Example of capacity expansion 83
- Example of migrate output 83
- Port Object Commands 85
- attribute 86
- /cx/px show firmware 87
- /cx/px show identify 87
- /cx/px show lspeed 87
- /cx/px show model 87
- /cx/px show serial 88
- /cx/px show smart 88
- /cx/px show ncq 88
- remove [noscan] [quiet] 90
- Phy Object Commands 91
- BBU Object Commands 92
- /cx/bbu show serial 94
- /cx/bbu show status 94
- /bbu show all 95
- /cx/ex show controllers 98
- /cx/ex/ show diag=helptext 99
- /cx/ex show slots 99
- /cx/ex show fans 99
- /cx/ex show temp 99
- show all 100
- Example: 102
- Enclosure Object Commands 103
- Help Commands 104
- Help with attributes 105
- Command Logging 109
- Return Code 109
- If you type: 110
Verwandte Produkte und Handbücher für RAID-Kontroller AMCC 3WARE 9590SE
(302 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern